Steinigke Showtechnic GmbH - your wholesale company for event technology. We only sell to commercial customers. All prices without tax.
Ordinamento
Prodotti per pagina:
1 2 3 4

OMNITRONIC  A-3603 Class-D 2.1 Amplifier

n° art. 10452370
Features
Dati tecnici

3-channel PA amplifier with SMPS - 4 ohms: 1 x 2000 W, 2 x 800 W

  • 3-channel PA amplifier with class D circuitry and switch mode power supply
  • Adjustable crossover frequency for satellites and subwoofer
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 3 level controls
  • LED VU meter and LEDs for activated protective circuit (protect) and overload (clip) per channel
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:100-240 V AC, 50/60 Hz
Power consumption:685 W (1/8 power)
Power output (RMS):
4 ohms:1 x 2000 W, 2 x 800 W
8 ohms:1 x 1000 W, 2 x 400 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>100 dB
Total harmonic distortion:<0.15 %
Damping factor:>500
Voltage gain:41.2 dB
Slew rate:>10 V/µsec
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:3 x XLR
Output connectors:3 x Speaker, 3 x XLR feed-through output
Circuitry:Class D
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, X-over frequency
LED indicators:protect, clip, 0 dB, - 5 dB, - 10 dB, - 20 dB (per channel)
Construction:steel chassis, aluminum front
Dimensions:483 x 410 x 100 mm
Rack installation with 2 U
Weight:9.3 kg
549,00 
Disponibile in 8 settimane

PSSO  DDA-1700 Amplifier

n° art. 10451684
Features
Dati tecnici

Stereo PA amplifier with SMPS, 2 x 850 W / 4 ohms

  • Stereo PA amplifier with class D circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:100-240 V AC, 50/60 Hz
Power consumption:150 W (1/8 power)
Power output (RMS):
Stereo, parallel at 4 ohms2 x 850 W
Stereo, parallel at 8 ohms2 x 500 W
8 ohms bridged1 x 1700 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>100 dB
Total harmonic distortion:<0.15 %
Damping factor:>500
Voltage gain:38.2 dB
Slew rate:>10 V/µsec
Input sensitivity:0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Circuitry:Class D
Protection:Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:protect, clip, -5 dB, -10 dB, -20 dB (per channel)
Construction:steel chassis, aluminum front
Dimensions:483 x 461 x 89 mm
Rack installation with 2 U
Weight:7 kg
359,00 
Disponibile in 5 settimane

PSSO  DDA-2500 Amplifier

n° art. 10451685
Features
Dati tecnici

Stereo PA amplifier with SMPS, 2 x 1250 W / 4 ohms

  • Stereo PA amplifier with class D circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:100-240 V AC, 50/60 Hz
Power consumption:200 W (1/8 power)
Power output (RMS):
Stereo, parallel at 4 ohms2 x 1250 W
Stereo, parallel at 8 ohms2 x 700 W
8 ohms bridged1 x 2500 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>100 dB
Total harmonic distortion:<0.15 %
Damping factor:>500
Voltage gain:39.7 dB
Slew rate:>10 V/µsec
Input sensitivity:0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Circuitry:Class D
Protection:Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:protect, clip, - 5 dB, - 10 dB, - 20 dB (per channel)
Construction:steel chassis, aluminum front
Dimensions:483 x 461 x 89 mm
Rack installation with 2 U
Weight:7.5 kg
399,00 
Disponibile in 5 settimane

PSSO  DDA-3500 Amplifier

n° art. 10451687
Features
Dati tecnici

Stereo PA amplifier with SMPS, 2 x 1750 W / 4 ohms

  • Stereo PA amplifier with class D circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:100-240 V AC, 50/60 Hz
Power consumption:300 W (1/8 power)
Power output (RMS):
Stereo, parallel 4 ohms2 x 1750 W
Stereo, parallel 8 ohms2 x 1000 W
8 ohms bridged1 x 3500 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>100 dB
Total harmonic distortion:<0.15 %
Damping factor:>500
Voltage gain:41.2 dB
Slew rate:>10 V/µsec
Input sensitivity:0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Circuitry:Class D
Protection:Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:protect, clip, - 5 dB, - 10 dB, - 20 dB (per channel)
Construction:steel chassis, aluminum front
Dimensions:483 x 461 x 89 mm
Rack installation with 2 U
Weight:8.5 kg
449,00 
Disponibile in 5 settimane

OMNITRONIC  DJP-700 Class D Amplifier

n° art. 10451601
Features
Dati tecnici

Compact stereo mixing amplifier, 2 x 300 W / 4 ohms

  • For quick-access music playback control in restaurants, fitness studios and retail locations
  • Efficient class D circuitry
  • Silent operation due to fanless cooling concept
  • Extremely low weight and height due to integrated switch mode power supply
  • 2 operating modes can be selected (stereo or bridged)
  • Speaker switch-on delay and auto limiters
  • 4 stereo line inputs
  • 1 mono microphone input with gain control on the front panel
  • Additional 3.5 mm connection on the front panel
  • Audio source selector
  • Controls for volume, bass and treble
  • Stereo master output
  • Extensive protective circuits
  • Robust steel chassis with aluminum front panel
Power supply:230 V AC, 50 Hz
Power consumption:130 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 300 W
stereo 8 ohms2 x 200 W
8 ohms bridged1 x 600 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>300
Distortion factor:0.05 %
Slew rate:14 V/µsec
S/N ratio:100 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input sensitivity:1 V
Input connectors:
Line 1-4:RCA L/R
Mic:combination XLR/6.3 mm jack, unbal.
Aux:3.5 stereo jack
Output connectors:
Master:RCA L/R
Speaker:screw connectors
Circuitry:class D
Control elements:power switch, source selector, level/tone controls, mode switch (stereo/bridged)
LED indicators:power
Protection circuits:softstart, short-circuit, overheat, clipping, overload, VHF signals, DC voltage
Construction:steel chassis, aluminum front
Dimensions (DxWxH):256 x 233 x 44 mm
Weight:2.2 kg
169,00 
Quest' articolo non è disponibile

OMNITRONIC  DJP-700P Class D Amplifier

n° art. 10451602
Features
Dati tecnici

Compact stereo mixing amplifier with player + Bluetooth, 2 x 300 W / 4 ohms

  • Compact stereo mixing amplifier 2 x 300 watts
  • For quick-access music playback control in restaurants, fitness studios and retail locations
  • Built-in audio player with Bluetooth receiver
  • Stream music wirelessly from your mobile devices (e.g. smartphone, tablet) via Bluetooth
  • USB 2.0 input and SD card slot
  • Efficient class D circuitry
  • Silent operation due to fanless cooling concept
  • Extremely low weight and height due to integrated switch mode power supply
  • 2 operating modes can be selected (stereo or bridged)
  • Speaker switch-on delay and auto limiters
  • 4 stereo line inputs
  • 1 mono microphone input with gain control on the front panel
  • Additional 3.5 mm connection on the front panel
  • Audio source selector
  • Controls for volume, bass and treble
  • Stereo master output
  • Extensive protective circuits
  • Robust steel chassis with aluminum front panel
Power supply:230 V AC, 50 Hz
Power consumption:130 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 300 W
stereo 8 ohms2 x 200 W
8 ohms bridged1 x 600 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>300
Distortion factor:0.05 %
Slew rate:14 V/µsec
S/N ratio:100 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input sensitivity:1 V
Input connectors:
Line 1-4:RCA L/R
Mic:combination XLR/6.3 mm jack, unbal.
Aux:3.5 stereo jack
Output connectors:
Master:RCA L/R
Speaker:screw connectors
Circuitry:class D
Control elements:power switch, source selector, level/tone controls, mode switch (stereo/bridged)
LED indicators:power
Protection circuits:softstart, short-circuit, overheat, clipping, overload, VHF signals, DC voltage
Construction:steel chassis, aluminum front
Dimensions (DxWxH):256 x 233 x 44 mm
Weight:2.2 kg
Audio player:
Playback format:MP3, WMA, WAV
Available storage media:USB devices and SD(HC) cards up to 32 GB
File system:FAT16/32
Bluetooth:
Carrier frequency:2.4 GHz
Range:approx. 10 m
189,00 
Quest' articolo non è disponibile

OMNITRONIC  EDP-3600 Class D Amplifier

n° art. 10451615
Features
Dati tecnici

Stereo PA amplifier with integrated SMPS 2 x 1700 W

  • Stereo PA amplifier with class D circuitry
  • Low weight and height due to integrated switch mode power supply
  • Speaker switch-on delay and auto limiters
  • 2 operating modes can be selected (stereo or bridged)
  • 2 level controls
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Complete protection set against short-circuit, overheat, clipping, overload and VHF signals
  • Electronically balanced inputs via XLR mounting jacks
  • Speaker outputs via lockable Speaker plugs
  • Robust steel chassis with aluminum front panel
  • Rack installation with 1 unit
Power supply:100-240 V AC, 50/60 Hz
Power consumption:1050 W (1/8 power)
Power output (RMS):
stereo 4 ohms2 x 1700 W
stereo 8 ohms2 x 1000 W
8 ohms bridged1 x 3600 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>250
Distortion factor:<0.1 %
Slew rate:20 V/µsec
S/N ratio:>95 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, 2 x XLR feed-through output
Circuitry:class D + PFC
Control elements:power switch, level control per channel, mode switch (stereo/bridged)
LED indicators:protect, clip, signal, -6 dB, -12 dB, -18 dB, -25 dB (per channel)
Protection circuits:softstart, short-circuit, overheat, clipping, overload and VHF signals
Construction:steel chassis, aluminum front
Dimensions (DxWxH):250 x 483 x 44 mm (19", 1 U)
Weight:4.6 kg
SALE 20 % risparmio
Azione da 07.06.2017 a 30.06.2018
599,00 €
479,00 
Stock basta per 12 settimane
Alternativa interessante, guardare in ogni caso!
OMNITRONIC XPA-2700 Amplifier

PSSO  HP-2400 Amplifier

n° art. 10451651
Features
Dati tecnici

High-power amplifier 2 x 1200 W/4 ohms

  • Class H technology
  • Power supply with softstart
  • High impulse stability
  • Stable metal housing
  • Plain design with aluminum front panel
  • Rack installation with 2 units
  • Complete protection set against overheat, overload, short-circuit, DC, softstart
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • Electronically balanced inputs via XLR/Jack mounting sockets
  • Outputs via lockable Speaker-plugs
  • Operation mode visible via LED display for Signal, Protect and Clip
  • Calibrated input controls for exact level control, power switch
  • Ground Lift switch against humming
  • Bridged switch for bridging
  • 30 Hz Low Cut on the rear panel
  • Combines superior sound quality with highest reliabilty at significant lower weight
  • Stable permanent power for all models
  • Reliable power amp for a wide range of applications
Power supply:230 V AC, 50 Hz
Power consumption:1300 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 1200 W
Stereo 8 ohms2 x 690 W
8 ohms bridged1 x 2400 W
Frequency range:20-20000 Hz
Signal-to-noise ratio:>88 dB
Total harmonic distortion:0.1 %
Damping factor:450
Voltage gain:34.3 dB
Slew rate:30 V/µsec.
Crosstalk:72 dB
Input sensitivity:0.77/1/1.4 V
Input impedance:10/20 kohms (bal./unbal.)
Input connectors:2 x XLR mounting socket
Output connectors:2 x Speaker (stereo), 1 x binding post (bridge)
Protection:Overheat, overload, short-circuit, DC, softstart
Cooling:2 fans
Controls:Power switch, input attenuators, mode switch (stereo/parallel/bridged), ground lift
Indicators:Signal, Clip, Protect, Power
Construction:Steel chassis, aluminum front panel
Dimensions:456 x 482 x 88 mm
Rack installation with 2 U
Weight:22 kg
SALE 34 % risparmio
Azione da 27.06.2017 a 30.06.2018
699,00 €
461,34 
Stock basta per 12 settimane

PSSO  HSP-1000 MK2 SMPS Amplifier

n° art. 10451682
Features
Dati tecnici

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:1000 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 500 W
Stereo 8 ohms2 x 310 W
8 ohms bridged1 x 1000 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.1 %
Damping factor:>200
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 400 x 89 mm
Rack installation with 2 U
Weight:8 kg
439,00 
Quest' articolo non è disponibile

PSSO  HSP-2800 MK2 SMPS Amplifier

n° art. 10451690
Features
Dati tecnici

Stereo PA amplifier with integrated SMPS, 2 x 1400 W

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:1500 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 1400 W
Stereo 8 ohms2 x 850 W
8 ohms bridged1 x 3000 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>90 dB
Total harmonic distortion:<0.1 %
Damping factor:>300
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, swtichable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection: Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 505 x 89 mm
Rack installation with 2 U
Weight:13 kg
829,00 
Stock basta per 12 settimane
1 2 3 4
Prodotti appena visti
Your request was successful sent.
Loader
Please wait while the page is loading...

We use cookies to ensure you get the best user experience on our website. By continuing, you accept the cookie use