Steinigke Showtechnic GmbH - your wholesale company for event technology. We only sell to commercial customers. All prices without tax.
Sorting
Products per page:
1 2

OMNITRONIC  A-3603 Class-D 2.1 Amplifier

Item no. 10452370
Features
Technical specifications

3-channel PA amplifier with crossover network - 4 ohms: 1 x 2000 W, 2 x 800 W

  • 3-channel PA amplifier with class D circuitry and switch mode power supply
  • Adjustable crossover frequency for satellites and subwoofer
  • 2.1 operation or 3-channel operation selectable
  • 3 level controls
  • LED VU meter and LEDs for activated protective circuit (protect) and overload (clip) per channel
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:100-240 V AC, 50/60 Hz
Power consumption:685 W (1/8 power)
Power output (RMS):
4 ohms:1 x 2000 W, 2 x 800 W
8 ohms:1 x 1000 W, 2 x 400 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>100 dB
Total harmonic distortion:<0.003 %
Damping factor:>500
Voltage gain:41.2 dB
Slew rate:>10 V/µsec
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:3 x XLR
Output connectors:3 x Speaker, 3 x XLR feed-through output
Circuitry:Class D
Controls:Power switch, input attenuators, mode switch 2/3 channels, X-over frequency
LED indicators:protect, clip, 0 dB, - 10 dB, - 20 dB (per channel)
Construction:steel chassis, aluminum front
Dimensions:483 x 410 x 100 mm
Rack installation with 2 U
Weight:9,3 kg
549,00 
available in approx. 4 wk(s)

PSSO  DDA-1700 Amplifier

Item no. 10451684
Features
Technical specifications

Stereo PA amplifier with SMPS, 2 x 850 W / 4 ohms

  • Stereo PA amplifier with class D circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:100-240 V AC, 50/60 Hz
Power consumption:150 W (1/8 power)
Power output (RMS):
Stereo, parallel at 4 ohms2 x 850 W
Stereo, parallel at 8 ohms2 x 500 W
8 ohms bridged1 x 1700 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>100 dB
Total harmonic distortion:<0.15 %
Damping factor:>500
Voltage gain:38.2 dB
Slew rate:>10 V/µsec
Input sensitivity:0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Circuitry:Class D
Protection:Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:protect, clip, -5 dB, -10 dB, -20 dB (per channel)
Construction:steel chassis, aluminum front
Dimensions:483 x 461 x 89 mm
Rack installation with 2 U
Weight:7 kg
359,00 
product incoming

PSSO  DDA-2500 Amplifier

Item no. 10451685
Features
Technical specifications

Stereo PA amplifier with SMPS, 2 x 1250 W / 4 ohms

  • Stereo PA amplifier with class D circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:100-240 V AC, 50/60 Hz
Power consumption:200 W (1/8 power)
Power output (RMS):
Stereo, parallel at 4 ohms2 x 1250 W
Stereo, parallel at 8 ohms2 x 700 W
8 ohms bridged1 x 2500 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>100 dB
Total harmonic distortion:<0.15 %
Damping factor:>500
Voltage gain:39.7 dB
Slew rate:>10 V/µsec
Input sensitivity:0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Circuitry:Class D
Protection:Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:protect, clip, - 5 dB, - 10 dB, - 20 dB (per channel)
Construction:steel chassis, aluminum front
Dimensions:483 x 461 x 89 mm
Rack installation with 2 U
Weight:7,5 kg
399,00 
product incoming

PSSO  DDA-3500 Amplifier

Item no. 10451687
Features
Technical specifications

Stereo PA amplifier with SMPS, 2 x 1750 W / 4 ohms

  • Stereo PA amplifier with class D circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:100-240 V AC, 50/60 Hz
Power consumption:300 W (1/8 power)
Power output (RMS):
Stereo, parallel 4 ohms2 x 1750 W
Stereo, parallel 8 ohms2 x 1000 W
8 ohms bridged1 x 3500 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>100 dB
Total harmonic distortion:<0.15 %
Damping factor:>500
Voltage gain:41.2 dB
Slew rate:>10 V/µsec
Input sensitivity:0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Circuitry:Class D
Protection:Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:protect, clip, - 5 dB, - 10 dB, - 20 dB (per channel)
Construction:steel chassis, aluminum front
Dimensions:483 x 461 x 89 mm
Rack installation with 2 U
Weight:8,5 kg
449,00 
product incoming

PSSO  HSP-2800 MK2 SMPS Amplifier

Item no. 10451690
Features
Technical specifications

Stereo PA amplifier with integrated SMPS, 2 x 1400 W

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:1500 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 1400 W
Stereo 8 ohms2 x 850 W
8 ohms bridged1 x 3000 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>90 dB
Total harmonic distortion:<0.1 %
Damping factor:>300
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, swtichable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 505 x 89 mm
Rack installation with 2 U
Height:8.9 cm
Width:48.3 cm
Weight:13 kg
:50.5 cm
829,00 
Stock for approx. 12 wk(s)

PSSO  HSP-4000 MK2 SMPS Amplifier

Item no. 10451694
Features
Technical specifications

Stereo PA amplifier with integrated SMPS, 2 x 2000 W

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:2000 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 2000 W
Stereo 8 ohms2 x 1200 W
8 ohms bridged1 x 4100 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.1 %
Damping factor:>200
Voltage gain:32 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 505 x 89 mm
Rack installation with 2 U
Height:8.9 cm
Width:48.3 cm
Weight:14 kg
:50.5 cm
799,00 
Stock for approx. 12 wk(s)

OMNITRONIC  MCD-2004 4-Channel Amplifier

Item no. 10452411
Features
Technical specifications

4-channel PA amplifier with SMPS, 4 ohms: 4 x 500 W, 8 ohms: 4 x 250 W

  • PA amplifier with integrated limiter for multi-zone applications
  • 4 x 500 W/4 ohms
  • 8-ohm bridge operation possible
  • Signal inputs via balanced XLR mounting jacks and terminal blocks
  • Speaker connection via terminal blocks
  • Tamper-proof level adjustment on the rear panel
  • 3-fold output meter with clip LED per channel
  • Speaker switch-on delay
  • Fan cooling
  • Robust steel chassis with aluminum front
  • Complete protection set against short-circuit, overheat, overload, and DC voltage overlay at the outputs
  • Rack installation with 3 units
Power supply:230 V AC, 50 Hz
Power consumption:350 W (1/8 power)
Power output sine:
4 ohms:4 x 500 W
8 ohms:4 x 250 W
8 ohms bridged:2 x 1000 W
Frequency range:22-25000 Hz
Damping factor:> 500
Distortion factor:< 0.003 %
SN ratio:120 dB
Slew rate:>10 V/µsec
Min. input sensitivity:2 V
Input impedance:12 kohms (unbalanced), 22 kohms (balanced)
Input connectors:XLR female, terminal blocks
Output connectors:Terminal blocks
Indicators:Level with clip per channel, bridged
Protection circuits:Softstart, short-circuit, overheat, overload and DC voltage
Construction:Steel chassis with aluminum front panel
Dimensions:483 x 388 x 101 mm
Weight:7,6 kg
329,00 
available in approx. 5 wk(s)

OMNITRONIC  MCD-3006 6-Channel Amplifier

Item no. 10452412
Features
Technical specifications

6-channel PA amplifier with SMPS, 4 ohms: 6 x 500 W, 8 ohms: 6 x 250 W

  • PA amplifier with integrated limiter for multi-zone applications
  • 6 x 500 W/4 ohms
  • 8-ohm bridge operation possible
  • Signal inputs via balanced XLR mounting jacks and terminal blocks
  • Speaker connection via terminal blocks
  • Tamper-proof level adjustment on the rear panel
  • 3-fold output meter with clip LED per channel
  • Speaker switch-on delay
  • Fan cooling
  • Robust steel chassis with aluminum front
  • Complete protection set against short-circuit, overheat, overload, and DC voltage overlay at the outputs
  • Rack installation with 3 units
Power supply:230 V AC, 50 Hz
Power consumption:525 W (1/8 power)
Power output sine:
4 ohms:6 x 500 W
8 ohms:6 x 250 W
8 ohms bridged:3 x 1000 W
Frequency range:22-25000 Hz
Damping factor:> 500
Distortion factor:< 0.003 %
SN ratio:120 dB
Slew rate:>10 V/µsec
Min. input sensitivity:2 V
Input impedance:12 kohms (unbalanced), 22 kohms (balanced)
Input connectors:XLR female, terminal blocks
Output connectors:Terminal blocks
Indicators:Level with clip per channel, bridged
Protection circuits:Softstart, short-circuit, overheat, overload and DC voltage
Construction:Steel chassis with aluminum front panel
Dimensions:483 x 388 x 101 mm
Weight:9 kg
459,00 
available in approx. 5 wk(s)

OMNITRONIC  MCD-4008 8-Channel Amplifier

Item no. 10452413
Features
Technical specifications

8-channel PA amplifier with SMPS, 4 ohms: 8 x 500 W, 8 ohms: 8 x 250 W

  • PA amplifier with integrated limiter for multi-zone applications
  • 8 x 150 W/4 ohms
  • 8-ohm bridge operation possible
  • Signal inputs via balanced XLR mounting jacks and terminal blocks
  • Speaker connection via terminal blocks
  • Tamper-proof level adjustment on the rear panel
  • 3-fold output meter with clip LED per channel
  • Speaker switch-on delay
  • Fan cooling
  • Robust steel chassis with aluminum front
  • Complete protection set against short-circuit, overheat, overload, and DC voltage overlay at the outputs
  • Rack installation with 3 units
Power supply:230 V AC, 50 Hz
Power consumption:700 W (1/8 power)
Power output sine:
4 ohms:8 x 500 W
8 ohms:8 x 250 W
8 ohms bridged:4 x 1000 W
Frequency range:22-25000 Hz
Damping factor:> 500
Distortion factor:< 0.003 %
SN ratio:120 dB
Slew rate:>10 V/µsec
Min. input sensitivity:2 V
Input impedance:12 kohms (unbalanced), 22 kohms (balanced)
Input connectors:XLR female, terminal blocks
Output connectors:Terminal blocks
Indicators:Level with clip per channel, bridged
Protection circuits:Softstart, short-circuit, overheat, overload and DC voltage
Construction:Steel chassis with aluminum front panel
Dimensions:483 x 388 x 101 mm
Weight:9,3 kg
599,00 
available in approx. 5 wk(s)

PSSO  PRIME System Amplifier DSP

Item no. 10451701
Features
Technical specifications

6 channel PA amp with SMPS, 2 x 2400 W, 4 x 800 W

  • 6-channel PA amplifier with high-performance DSP, freely programmable
  • Sample frequency: 96 kHz and 64-bit technology
  • Premium components ensure excellent sound features
  • Efficient class D amplifier circuitry
  • 2 Pascal amplifier modules
  • 4 analog inputs and 2 digital AES/EBU interfaces (XLR)
  • 4 analog link outputs (XLR)
  • 2 Neutrik Speakon outputs
  • Neutrik Powercon mains input
  • Real-time remote control via built-in Ethernet LAN interface
  • User-friendly software for PC and Mac included
  • 80 presets can be stored and activated
  • Manual control via encoder, LCD screen and buttons at the front panel
  • 120 dB dynamic range
  • Flexible routing
  • 10 parametric EQ
  • X-Over: Bessel, Linkwitz-Riley, Butterworth with 24 dB/octave
  • Delay
  • Limiter and noise gate
  • Phase reverse
  • Password protection
  • Low weight and height due to integrated switch mode power supply
  • Automatic power supply adaption between 100 and 240 volts without power selector
  • Intelligent mains fuse protection
  • Input current limiter
  • Protection against turn-on and turn-off transients
  • DC protection of outputs
  • Under and over voltage protection
  • Temperature-controlled air-cooling
  • High damping factor> 1000
  • Low distortion, THD+N < 0.05 %
  • Rugged steel chassis with anodized aluminum front panel
  • Rack installation with 2 units
  • Windows XP, Vista, 7, 8 and Mac OS X 10.5.8 and better
  • Made in Germany
Power supply:100-240 V AC, 50/60 Hz
Power consumption:920 W (1/8 power)
Power output (RMS):
Channel 1, 4:2400 W at 4 ohms
1500 W at 8 ohms
Channel 2, 3, 5, 6:800 W at 4 ohms
400 W at 8 ohms
Channel 2/3, 5/6 bridged:2 x 1500 W at 8 ohms
Frequency range:20-40000 Hz
Signal-to-Noise ratio:>120 dB
Total harmonic distortion:<0.05 % (20-20000 Hz, 8 ohms)
Damping factor:>1000 (8 ohms, 1 kHz)
Voltage gain:LF 32 dB, MF 26 dB
Analog inputs:4 x XLR
Digital inputs:2 x AES/EBU (XLR)
Analog output:4 x XLR (link)
2 x 8-pin Speakon
Communication:LAN (TCP/IP)
Protection:Intelligent mains fuse protection, input current limiter,
protection against turn-on and turn-off transients, DC protection of outputs,
under and over voltage protection
Cooling:temperature-controlled air-cooling
Controls:Power switch, encoder, menu, exit
LED indicators:Protect, Peak, Limit, Signal
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 482 x 88 mm
Rack installation with 2 U
Weight:12 kg
3.150,00 
Stock for approx. 12 wk(s)
1 2
Last seen products
Your request was successful sent.
Loader
Please wait while the page is loading...

We use cookies to ensure you get the best user experience on our website. By continuing, you accept the cookie use