Steinigke Showtechnic GmbH - your wholesale company for event technology. We only sell to commercial customers. All prices without tax.
Сортировать
Товаров на странице:
1 2

PSSO  HSP-1000 MK2 SMPS Amplifier

Арт. № 10451682
Свойства
Технические данные

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz ~
Power consumption:1000 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 500 W
Stereo 8 ohms2 x 310 W
8 ohms bridged1 x 1000 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.1 %
Damping factor:>200
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 400 x 89 mm
Rack installation with 2 U
Weight:8 kg
Shipping weight:9.20 kg
439,00
будет в наличии до 12 недели

PSSO  HSP-2100 MK2 SMPS Amplifier

Арт. № 10451686
Свойства
Технические данные

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz ~
Power consumption:1500 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 1050 W
Stereo 8 ohms2 x 650 W
8 ohms bridged1 x 2200 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>90 dB
Total harmonic distortion:<0.1 %
Damping factor:>300
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, swtichable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 400 x 89 mm
Rack installation with 2 U
Weight:10 kg
Shipping weight:11.50 kg
599,00
В наличии нет

PSSO  HSP-2800 MK2 SMPS Amplifier

Арт. № 10451690
Свойства
Технические данные

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz ~
Power consumption:1500 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 1400 W
Stereo 8 ohms2 x 850 W
8 ohms bridged1 x 3000 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>90 dB
Total harmonic distortion:<0.1 %
Damping factor:>300
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, swtichable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection: Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 505 x 89 mm
Rack installation with 2 U
Weight:13 kg
Shipping weight:14.80 kg
829,00
будет в наличии до 12 недели

PSSO  HSP-4000 MK2 SMPS Amplifier

Арт. № 10451694
Свойства
Технические данные

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz ~
Power consumption:2000 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 2000 W
Stereo 8 ohms2 x 1200 W
8 ohms bridged1 x 4100 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.1 %
Damping factor:>200
Voltage gain:32 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 505 x 89 mm
Rack installation with 2 U
Weight:14 kg
Shipping weight:15.30 kg
899,00
будет в наличии до 12 недели

PSSO  PRIME System Amplifier DSP

Арт. № 10451701
Свойства
Технические данные

DSP PA amplifier with real-time network communication

  • 6-channel PA amplifier with high-performance DSP, freely programmable
  • Sample frequency: 96 kHz and 64-bit technology
  • Premium components ensure excellent sound features
  • Efficient class D amplifier circuitry
  • 2 Pascal amplifier modules
  • 4 analog inputs and 2 digital AES/EBU interfaces (XLR)
  • 4 analog link outputs (XLR)
  • 2 Neutrik Speakon outputs
  • Neutrik Powercon mains input
  • Real-time remote control via built-in Ethernet LAN interface
  • User-friendly software for PC and Mac included
  • 80 presets can be stored and activated
  • Manual control via encoder, LCD screen and buttons at the front panel
  • 120 dB dynamic range
  • Flexible routing
  • 10 parametric EQ
  • X-Over: Bessel, Linkwitz-Riley, Butterworth with 24 dB/octave
  • Delay
  • Limiter and noise gate
  • Phase reverse
  • Password protection
  • Low weight and height due to integrated switch mode power supply
  • Automatic power supply adaption between 100 and 240 volts without power selector
  • Intelligent mains fuse protection
  • Input current limiter
  • Protection against turn-on and turn-off transients
  • DC protection of outputs
  • Under and over voltage protection
  • Temperature-controlled air-cooling
  • High damping factor> 1000
  • Low distortion, THD+N < 0.05 %
  • Rugged steel chassis with anodized aluminum front panel
  • Rack installation with 2 units
  • Windows XP, Vista, 7, 8 and Mac OS X 10.5.8 and better
  • Made in Germany
Power supply:100-240 V AC, 50/60 Hz ~
Power consumption:920 W (1/8 power)
Power output (RMS):
Channel 1, 4:2400 W at 4 ohms
1500 W at 8 ohms
Channel 2, 3, 5, 6:800 W at 4 ohms
400 W at 8 ohms
Channel 2/3, 5/6 bridged:2 x 1500 W at 8 ohms
Frequency range:20-40000 Hz
Signal-to-Noise ratio:>120 dB
Total harmonic distortion:<0.05 % (20-20000 Hz, 8 ohms)
Damping factor:>1000 (8 ohms, 1 kHz)
Voltage gain:LF 32 dB, MF 26 dB
Analog inputs:4 x XLR
Digital inputs:2 x AES/EBU (XLR)
Analog output:4 x XLR (link)
2 x 8-pin Speakon
Communication:LAN (TCP/IP)
Protection:Intelligent mains fuse protection, input current limiter,
protection against turn-on and turn-off transients, DC protection of outputs,
under and over voltage protection
Cooling:temperature-controlled air-cooling
Controls:Power switch, encoder, menu, exit
LED indicators:Protect, Peak, Limit, Signal
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 482 x 88 mm
Rack installation with 2 U
Weight:12 kg
Shipping weight:13.50 kg
3.150,00
будет в наличии до 12 недели

PSSO  QCA-10000 4-Channel SMPS Amplifier

Арт. № 10451697
Свойства
Технические данные

4-channel PA amplifier with integrated SMPS

  • 4-channel PA amplifier with class I circuitry
  • 4 x 2100 W/4 ohms
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 4 level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
  • Neutrik Speakon outputs
Power supply:230 V AC, 50 Hz ~
Power consumption:1150 W (1/8 power)
Power output (RMS):
2 ohms4 x 2500 W
4 ohms4 x 2100 W
8 ohms4 x 1300 W
4 ohms bridged2 x 5000 W
8 ohms bridged2 x 4200 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.05 %
Damping factor:>800
Slew rate:>10 V/µsec
Crosstalk:>65 dB
Input sensitivity:0.775 V/1.0 V/1.4 V/38 dB/32 dB/26 dB, switchable
Voltage gain:40.3 dB (0.775 V), 38 dB (1.0 V), 35.1 dB (1.4 V)
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Protection: Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:Protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 445 x 89 mm
Rack installation with 2 U
Weight:15.7 kg
Shipping weight:15.80 kg
1.499,00
будет в наличии до 12 недели

PSSO  QCA-6400 4-Channel SMPS Amplifier

Арт. № 10451696
Свойства
Технические данные

4-channel PA amplifier with integrated SMPS

  • 4-channel PA amplifier with class I circuitry
  • 4 x 1400 W/4 ohms
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 4 level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
  • Neutrik Speakon outputs
Power supply:230 V AC, 50 Hz ~
Power consumption:820 W (1/8 power)
Power output (RMS):
2 ohms4 x 1600 W
4 ohms4 x 1400 W
8 ohms4 x 800 W
4 ohms bridged2 x 3200 W
8 ohms bridged2 x 2800 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.05 %
Damping factor:>800
Slew rate:>10 V/µsec
Crosstalk:>65 dB
Input sensitivity:0.775 V/1.0 V/1.4 V/38 dB/32 dB/26 dB, switchable
Voltage gain:40.3 dB (0.775 V), 38 dB (1.0 V), 35.1 dB (1.4 V)
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Protection: Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:Protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 445 x 89 mm
Rack installation with 2 U
Weight:15.5 kg
Shipping weight:15.30 kg
1.299,00
будет в наличии до 12 недели

OMNITRONIC  SMA-1000 Amplifier

Арт. № 10451084
Свойства
Технические данные

Stereo PA amplifier with integrated limiter and SMPS 2 x 500 W/4 ohms

  • Low weight and height due to integrated switch-mode power supply
  • Temperature-controlled fan, particularly quiet during operation
  • Limiter and speaker switch-on delay
  • Switchable bass-boost at 80 Hz with 6 dB level increase
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • Selectable input sensitivity
  • 2 level controls
  • 3 LEDs for each channel for activated protective circuit (protect) overload (clip) and signal
  • 2 LEDs for parallel and bridge operation
  • Complete protection set against short-circuit, overheat, DC voltage and VHF signals
  • Electronically balanced inputs via XLR mounting jacks, with feed-through output (stereo RCA/6.3 mm jack)
  • Speaker outputs via lockable Speaker plugs
  • Class AB circuitry
  • Robust steel chassis
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz ~
Power consumption:598 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 482 W
stereo 8 ohms2 x 340 W
8 ohms bridged1 x 1000 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>150
Distortion factor:0.05 %
Slew rate:>20 V/µsec
S/N ratio:>90 dB
Channel seperation:>70 dB/ 1 kHz
Input sensitivity:26 dB/32 dB (2.48 V/1.244 V), switchable
Voltage gain:26 dB/32 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:stereo XLR
Output connectors:stereo Speaker, feed-through output (stereo RCA, stereo 6.3 mm jack)
Circuitry:class AB
Control elements:power switch, level control per channel, mode switch (stereo/parallel/bridged), sensitivity selector, peak filter selector
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Protection circuits:short-circuit, overheat, DC voltage, VHF signals, softstart
Construction:steel chassis
Dimensions (DxWxH):390 x 483 x 92 mm (19", 2 U)
Weight:7 kg
Shipping weight:9.65 kg
359,00
будет в наличии до 12 недели

OMNITRONIC  SMA-1500 Amplifier

Арт. № 10451086
Свойства
Технические данные

Stereo PA amplifier with integrated limiter and SMPS 2 x 750 W/4 ohms

  • Low weight and height due to integrated switch-mode power supply
  • Temperature-controlled fan, particularly quiet during operation
  • Limiter and speaker switch-on delay
  • Switchable bass-boost at 80 Hz with 6 dB level increase
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • Selectable input sensitivity
  • 2 level controls
  • 3 LEDs for each channel for activated protective circuit (protect) overload (clip) and signal
  • 2 LEDs for parallel and bridge operation
  • Complete protection set against short-circuit, overheat, DC voltage and VHF signals
  • Electronically balanced inputs via XLR mounting jacks, with feed-through output (stereo RCA/6.3 mm jack)
  • Speaker outputs via lockable Speaker plugs
  • SMA-1500 and SMA-2000 with additional pairs of screw terminals for 8 ohms bridge operation
  • Class 2 H circuitry
  • Robust steel chassis
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz ~
Power consumption:522 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 743 W
stereo 8 ohms2 x 480 W
8 ohms bridged1 x 1500 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>150
Distortion factor:0.05 %
Slew rate:>20 V/µsec
S/N ratio:>90 dB
Channel seperation:>70 dB/ 1 kHz
Input sensitivity:26 dB/32 dB (3.1 V/1.55 V), switchable
Voltage gain:26 dB/32 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:stereo XLR
Output connectors:stereo Speaker, 2 pairs of screw terminals, feed-through output (stereo RCA, stereo 6.3 mm jack)
Circuitry:class 2 H
Control elements:power switch, level control per channel, mode switch (stereo/parallel/bridged), sensitivity selector, peak filter selector
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Protection circuits:short-circuit, overheat, DC voltage, VHF signals, softstart
Construction:steel chassis
Dimensions (DxWxH):390 x 483 x 92 mm (19", 2 U)
Weight:9 kg
Shipping weight:11.80 kg
479,00
будет в наличии до 12 недели

OMNITRONIC  SMA-2000 Amplifier

Арт. № 10451088
Свойства
Технические данные

Stereo PA amplifier with integrated limiter and SMPS 2 x 1000 W/4 ohms

  • Low weight and height due to integrated switch-mode power supply
  • Temperature-controlled fan, particularly quiet during operation
  • Limiter and speaker switch-on delay
  • Switchable bass-boost at 80 Hz with 6 dB level increase
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • Selectable input sensitivity
  • 2 level controls
  • 3 LEDs for each channel for activated protective circuit (protect) overload (clip) and signal
  • 2 LEDs for parallel and bridge operation
  • Complete protection set against short-circuit, overheat, DC voltage and VHF signals
  • Electronically balanced inputs via XLR mounting jacks, with feed-through output (stereo RCA/6.3 mm jack)
  • Speaker outputs via lockable Speaker plugs
  • SMA-1500 and SMA-2000 with additional pairs of screw terminals for 8 ohms bridge operation
  • Class 2 H circuitry
  • Robust steel chassis
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz ~
Power consumption:575 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 1000 W
stereo 8 ohms2 x 637 W
8 ohms bridged1 x 2000 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>150
Distortion factor:0.05 %
Slew rate:>20 V/µsec
S/N ratio:>90 dB
Channel seperation:>70 dB/ 1 kHz
Input sensitivity:26 dB/32 dB (3.46 V/1.73 V), switchable
Voltage gain:26 dB/32 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:stereo XLR
Output connectors:stereo Speaker, 2 pairs of screw terminals, feed-through output (stereo RCA, stereo 6.3 mm jack)
Circuitry:class 2 H
Control elements:power switch, level control per channel, mode switch (stereo/parallel/bridged), sensitivity selector, peak filter selector
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Protection circuits:short-circuit, overheat, DC voltage, VHF signals, softstart
Construction:steel chassis
Dimensions (DxWxH):390 x 483 x 92 mm (19", 2 U)
Weight:9 kg
Shipping weight:12.00 kg
559,00
будет в наличии до 12 недели
1 2
Вы уже просмотрели
Ваш запрос успешно отправлен.
Loader
Страница загружается...

We use cookies to ensure you get the best user experience on our website. By continuing, you accept the cookie use