Steinigke Showtechnic GmbH - your wholesale company for event technology. We only sell to commercial customers. All prices without tax.
Сортировать
Товаров на странице:
1 2 3 4

OMNITRONIC  DJP-700 Class D Amplifier

Арт. № 10451601
Свойства
Технические данные

Compact stereo mixing amplifier, 2 x 300 W

  • For quick-access music playback control in restaurants, fitness studios and retail locations
  • Efficient class D circuitry
  • Silent operation due to fanless cooling concept
  • Extremely low weight and height due to integrated switch mode power supply
  • 2 operating modes can be selected (stereo or bridged)
  • Speaker switch-on delay and auto limiters
  • 4 stereo line inputs
  • 1 mono microphone input with gain control on the front panel
  • Additional 3.5 mm connection on the front panel
  • Audio source selector
  • Controls for volume, bass and treble
  • Stereo master output
  • Extensive protective circuits
  • Robust steel chassis with aluminum front panel
Power supply:230 V AC, 50 Hz
Power consumption:130 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 300 W
stereo 8 ohms2 x 200 W
8 ohms bridged1 x 600 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>300
Distortion factor:0.05 %
Slew rate:14 V/µsec
S/N ratio:100 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input sensitivity:1 V
Input connectors:
Line 1-4:RCA L/R
Mic:combination XLR/6.3 mm jack, unbal.
Aux:3.5 stereo jack
Output connectors:
Master:RCA L/R
Speaker:screw connectors
Circuitry:class D
Control elements:power switch, source selector, level/tone controls, mode switch (stereo/bridged)
LED indicators:power
Protection circuits:softstart, short-circuit, overheat, clipping, overload, VHF signals, DC voltage
Construction:steel chassis, aluminum front
Dimensions (DxWxH):256 x 233 x 44 mm
Weight:2.2 kg
169,00 
В наличии нет

OMNITRONIC  DJP-700P Class D Amplifier

Арт. № 10451602
Свойства
Технические данные

Compact stereo mixing amplifier with audio player and Bluetooth, 2 x 300 watts

  • Compact stereo mixing amplifier 2 x 300 watts
  • For quick-access music playback control in restaurants, fitness studios and retail locations
  • Built-in audio player with Bluetooth receiver
  • Stream music wirelessly from your mobile devices (e.g. smartphone, tablet) via Bluetooth
  • USB 2.0 input and SD card slot
  • Efficient class D circuitry
  • Silent operation due to fanless cooling concept
  • Extremely low weight and height due to integrated switch mode power supply
  • 2 operating modes can be selected (stereo or bridged)
  • Speaker switch-on delay and auto limiters
  • 4 stereo line inputs
  • 1 mono microphone input with gain control on the front panel
  • Additional 3.5 mm connection on the front panel
  • Audio source selector
  • Controls for volume, bass and treble
  • Stereo master output
  • Extensive protective circuits
  • Robust steel chassis with aluminum front panel
Power supply:230 V AC, 50 Hz
Power consumption:130 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 300 W
stereo 8 ohms2 x 200 W
8 ohms bridged1 x 600 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>300
Distortion factor:0.05 %
Slew rate:14 V/µsec
S/N ratio:100 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input sensitivity:1 V
Input connectors:
Line 1-4:RCA L/R
Mic:combination XLR/6.3 mm jack, unbal.
Aux:3.5 stereo jack
Output connectors:
Master:RCA L/R
Speaker:screw connectors
Circuitry:class D
Control elements:power switch, source selector, level/tone controls, mode switch (stereo/bridged)
LED indicators:power
Protection circuits:softstart, short-circuit, overheat, clipping, overload, VHF signals, DC voltage
Construction:steel chassis, aluminum front
Dimensions (DxWxH):256 x 233 x 44 mm
Weight:2.2 kg
Audio player:
Playback format:MP3, WMA, WAV
Available storage media:USB devices and SD(HC) cards up to 32 GB
File system:FAT16/32
Bluetooth:
Carrier frequency:2.4 GHz
Range:approx. 10 m
189,00 
В наличии нет

OMNITRONIC  EDP-3600 Class D Amplifier

Арт. № 10451615
Свойства
Технические данные

Stereo PA amplifier with integrated SMPS 2 x 1700 W

  • Stereo PA amplifier with class D circuitry
  • Low weight and height due to integrated switch mode power supply
  • Speaker switch-on delay and auto limiters
  • 2 operating modes can be selected (stereo or bridged)
  • 2 level controls
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Complete protection set against short-circuit, overheat, clipping, overload and VHF signals
  • Electronically balanced inputs via XLR mounting jacks
  • Speaker outputs via lockable Speaker plugs
  • Robust steel chassis with aluminum front panel
  • Rack installation with 1 unit
Power supply:100-240 V AC, 50/60 Hz
Power consumption:1050 W (1/8 power)
Power output (RMS):
stereo 4 ohms2 x 1700 W
stereo 8 ohms2 x 1000 W
8 ohms bridged1 x 3600 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>250
Distortion factor:<0.1 %
Slew rate:20 V/µsec
S/N ratio:>95 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, 2 x XLR feed-through output
Circuitry:class D + PFC
Control elements:power switch, level control per channel, mode switch (stereo/bridged)
LED indicators:protect, clip, signal, -6 dB, -12 dB, -18 dB, -25 dB (per channel)
Protection circuits:softstart, short-circuit, overheat, clipping, overload and VHF signals
Construction:steel chassis, aluminum front
Dimensions (DxWxH):250 x 483 x 44 mm (19", 1 U)
Weight:4.6 kg
РАСПРОДАЖА 20 % СКИДКИ
Акция с 07.06.2017 по 30.06.2018
599,00 €
479,00 
будет в наличии до 12 недели
Интересная альтернатива, пожалуйста, посмотрите!
OMNITRONIC XPA-2700 Amplifier

PSSO  HP-2400 Amplifier

Арт. № 10451651
Свойства
Технические данные

High-power amplifier 2 x 1200 W/4 ohms

  • Class H technology
  • Power supply with softstart
  • High impulse stability
  • Stable metal housing
  • Plain design with aluminum front panel
  • Rack installation with 2 units
  • Complete protection set against overheat, overload, short-circuit, DC, softstart
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • Electronically balanced inputs via XLR/Jack mounting sockets
  • Outputs via lockable Speaker-plugs
  • Operation mode visible via LED display for Signal, Protect and Clip
  • Calibrated input controls for exact level control, power switch
  • Ground Lift switch against humming
  • Bridged switch for bridging
  • 30 Hz Low Cut on the rear panel
  • Combines superior sound quality with highest reliabilty at significant lower weight
  • Stable permanent power for all models
  • Reliable power amp for a wide range of applications
Power supply:230 V AC, 50 Hz
Power consumption:1300 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 1200 W
Stereo 8 ohms2 x 690 W
8 ohms bridged1 x 2400 W
Frequency range:20-20000 Hz
Signal-to-noise ratio:>88 dB
Total harmonic distortion:0.1 %
Damping factor:450
Voltage gain:34.3 dB
Slew rate:30 V/µsec.
Crosstalk:72 dB
Input sensitivity:0.77/1/1.4 V
Input impedance:10/20 kohms (bal./unbal.)
Input connectors:2 x XLR mounting socket
Output connectors:2 x Speaker (stereo), 1 x binding post (bridge)
Protection:Overheat, overload, short-circuit, DC, softstart
Cooling:2 fans
Controls:Power switch, input attenuators, mode switch (stereo/parallel/bridged), ground lift
Indicators:Signal, Clip, Protect, Power
Construction:Steel chassis, aluminum front panel
Dimensions:456 x 482 x 88 mm
Rack installation with 2 U
Weight:22 kg
РАСПРОДАЖА 34 % СКИДКИ
Акция с 27.06.2017 по 30.06.2018
699,00 €
461,34 
будет в наличии до 12 недели

PSSO  HSP-1000 MK2 SMPS Amplifier

Арт. № 10451682
Свойства
Технические данные

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:1000 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 500 W
Stereo 8 ohms2 x 310 W
8 ohms bridged1 x 1000 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.1 %
Damping factor:>200
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 400 x 89 mm
Rack installation with 2 U
Weight:8 kg
439,00 
В наличии нет

PSSO  HSP-2800 MK2 SMPS Amplifier

Арт. № 10451690
Свойства
Технические данные

Stereo PA amplifier with integrated SMPS, 2 x 1400 W

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:1500 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 1400 W
Stereo 8 ohms2 x 850 W
8 ohms bridged1 x 3000 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>90 dB
Total harmonic distortion:<0.1 %
Damping factor:>300
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, swtichable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection: Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 505 x 89 mm
Rack installation with 2 U
Weight:13 kg
829,00 
будет в наличии до 12 недели

PSSO  HSP-4000 MK2 SMPS Amplifier

Арт. № 10451694
Свойства
Технические данные

Stereo PA amplifier with integrated SMPS, 2 x 2000 W

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:2000 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 2000 W
Stereo 8 ohms2 x 1200 W
8 ohms bridged1 x 4100 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.1 %
Damping factor:>200
Voltage gain:32 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 505 x 89 mm
Rack installation with 2 U
Weight:14 kg
722,93 
будет в наличии до 12 недели

OMNITRONIC  MCP-4150 4-Channel Amplifier

Арт. № 10452410
Свойства
Технические данные

4-channel PA amplifier with integrated limiter 4 x 150 W/4 ohms

  • PA amplifier with integrated limiter for multi-zone applications
  • 4 x 150 W/4 ohms
  • 8-ohm bridge operation possible
  • Signal inputs via balanced XLR mounting jacks or terminal blocks
  • Speaker connection via terminal blocks
  • High pass filter, low pass filter can be switched on additionally for each channel
  • Tamper-proof level adjustment on the rear panel
  • 7-fold output meter with clip LED per channel
  • Speaker switch-on delay
  • Groundlift switch against humming
  • Fan cooling
  • Robust steel chassis with aluminum front
  • Complete protection set against short-circuit, overheat, overload, and DC voltage overlay at the outputs
  • Rack installation with 3 units
Power supply:115/230 V AC, 50/60 Hz
Power consumption:900 W
Power output sine:
4 ohms:4 x 150 W
8 ohms:4 x 100 W
8 ohms bridged:2 x 300 W
Frequency range:22-25000 Hz
Damping factor:>200
Distortion factor:0.01 %
SN ratio:102 dB
Channel separation (at 1 kHz):61 dB
Slew rate:>30 V/µsec
Min. input sensitivity:0.77 V
Input impedance:12 kohms (unbalanced), 22 kohms (balanced)
Input connectors:4 x XLR female, 4 x terminal block
Output connectors:4 x terminal block
Control elements:Power switch, level control per channel, crossover on/off per channel, high/low pass per channel, mode switch (stereo/bridged)
Indicators:Level with clip per channel, bridged
Protection circuits:Softstart, short-circuit, overheat, overload and DC voltage
Construction:Steel chassis with aluminum front panel
Dimensions:310 x 482 x 132 mm
Minimum mounting depth:320 mm
Weight:16 kg
399,00 
будет в наличии до 12 недели

OMNITRONIC  MCP-6150 6-Channel Amplifier

Арт. № 10452420
Свойства
Технические данные

6-channel PA amplifier with integrated limiter 6 x 150 W/4 ohms

  • PA amplifier with integrated limiter for multi-zone applications
  • 6 x 150 W/4 ohms
  • 8-ohm bridge operation possible
  • Signal inputs via balanced XLR mounting jacks or terminal blocks
  • Speaker connection via terminal blocks
  • High pass filter, low pass filter can be switched on additionally for each channel
  • Tamper-proof level adjustment on the rear panel
  • 7-fold output meter with clip LED per channel
  • Speaker switch-on delay
  • Groundlift switch against humming
  • Fan cooling
  • Robust steel chassis with aluminum front
  • Complete protection set against short-circuit, overheat, overload, and DC voltage overlay at the outputs
  • Rack installation with 3 units
Power supply:115/230 V AC, 50/60 Hz
Power consumption:1400 W
Power output sine:
4 ohms:6 x 150 W
8 ohms:6 x 100 W
8 ohms bridged:3 x 300 W
Frequency range:22-25000 Hz
Damping factor:>200
Distortion factor:0.01 %
SN ratio:97 dB
Channel separation (at 1 kHz):51 dB
Slew rate:>30 V/µsec
Min. input sensitivity:0.77 V
Input impedance:12 kohms (unbalanced), 22 kohms (balanced)
Input connectors:6 x XLR female, 6 x terminal block
Output connectors:6 x terminal block
Control elements:Power switch, level control per channel, crossover on/off per channel, high/low pass per channel, mode switch (stereo/bridged)
Indicators:Level with clip per channel, bridged
Protection circuits:Softstart, short-circuit, overheat, overload and DC voltage
Construction:Steel chassis with aluminum front panel
Dimensions:310 x 482 x 132 mm
Minimum mounting depth:320 mm
Weight:17.5 kg
449,00 
будет в наличии до 6 недели

OMNITRONIC  MCP-8150 8-Channel Amplifier

Арт. № 10452430
Свойства
Технические данные

8-channel PA amplifier with integrated limiter 8 x 150 W/4 ohms

  • PA amplifier with integrated limiter for multi-zone applications
  • 8 x 150 W/4 ohms
  • 8-ohm bridge operation possible
  • Signal inputs via balanced XLR mounting jacks or terminal blocks
  • Speaker connection via terminal blocks
  • High pass filter, low pass filter can be switched on additionally for each channel
  • Tamper-proof level adjustment on the rear panel
  • 7-fold output meter with clip LED per channel
  • Speaker switch-on delay
  • Groundlift switch against humming
  • Fan cooling
  • Robust steel chassis with aluminum front
  • Complete protection set against short-circuit, overheat, overload, and DC voltage overlay at the outputs
  • Rack installation with 3 units
Power supply:115/230 V AC, 50/60 Hz
Power consumption:1850 W
Power output sine:
4 ohms:8 x 150 W
8 ohms:8 x 100 W
8 ohms bridged:4 x 300 W
Frequency range:22-25000 Hz
Damping factor:>200
Distortion factor:0.01 %
SN ratio:90 dB
Channel separation (at 1 kHz):51 dB
Min. input sensitivity:0.77 V
Slew rate:>30 V/µsec
Input impedance:12 kohms (unbalanced), 22 kohms(balanced)
Input connectors:8 x XLR female, 8 x terminal block
Output connectors:8 x terminal block
Control elements:Power switch, level control per channel, crossover on/off per channel, high/low pass per channel, mode switch (stereo/bridged)
Indicators:Level with clip per channel, bridged
Protection circuits:Softstart, short-circuit, overheat, overload and DC voltage
Construction:Steel chassis with aluminum front panel
Dimensions:310 x 482 x 132 mm
Minimum mounting depth:320 mm
Weight:19 kg
515,00 
будет в наличии до 12 недели
1 2 3 4
Вы уже просмотрели
Ваш запрос успешно отправлен.
Loader
Страница загружается...

We use cookies to ensure you get the best user experience on our website. By continuing, you accept the cookie use