OMNITRONIC A-3603 Class-D 2.1 Amplifier
Art. n° 10452370
3-channel PA amplifier with SMPS - 4 ohms: 1 x 2000 W, 2 x 800 W
- 3-channel PA amplifier with class D circuitry and switch mode power supply
- Adjustable crossover frequency for satellites and subwoofer
- 3 operating modes can be selected (stereo, parallel or bridged)
- 3 level controls
- LED VU meter and LEDs for activated protective circuit (protect) and overload (clip) per channel
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs
- Rugged steel chassis with aluminum front panel
- Rack installation with 2 units
Power supply: | 100-240 V AC, 50/60 Hz |
Power consumption: | 685 W (1/8 power) |
Power output (RMS): | |
4 ohms: | 1 x 2000 W, 2 x 800 W |
8 ohms: | 1 x 1000 W, 2 x 400 W |
Frequency range: | 20-20000 Hz |
Signal-to-Noise ratio: | >100 dB |
Total harmonic distortion: | <0.15 % |
Damping factor: | >500 |
Voltage gain: | 41.2 dB |
Slew rate: | >10 V/µsec |
Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
Input connectors: | 3 x XLR |
Output connectors: | 3 x Speaker, 3 x XLR feed-through output |
Circuitry: | Class D |
Controls: | Power switch, input attenuators, mode switch stereo/parallel/bridged, X-over frequency |
LED indicators: | protect, clip, 0 dB, - 5 dB, - 10 dB, - 20 dB (per channel) |
Construction: | steel chassis, aluminum front |
Dimensions: | 483 x 410 x 100 mm |
Rack installation with 2 U | |
Weight: | 9.3 kg |
Suivre cet article
Question sur le produit?
549,00 €
Disponible dans environ 8 semaine(s)
PSSO DDA-1700 Amplifier
Art. n° 10451684
Stereo PA amplifier with SMPS, 2 x 850 W / 4 ohms
- Stereo PA amplifier with class D circuitry
- Low weight and height due to integrated switch mode power supply
- Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
- Limiter and speaker switch-on delay
- 3 operating modes can be selected (stereo, parallel or bridged)
- 2 calibrated level controls for precise level adjustment
- Input sensitivity adjustable
- LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
- Highly efficient front-to-rear air routing
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs and screw terminals
- Rugged steel chassis with aluminum front panel
- Rack installation with 2 units
Power supply: | 100-240 V AC, 50/60 Hz |
Power consumption: | 150 W (1/8 power) |
Power output (RMS): | |
Stereo, parallel at 4 ohms | 2 x 850 W |
Stereo, parallel at 8 ohms | 2 x 500 W |
8 ohms bridged | 1 x 1700 W |
Frequency range: | 20-20000 Hz |
Signal-to-Noise ratio: | >100 dB |
Total harmonic distortion: | <0.15 % |
Damping factor: | >500 |
Voltage gain: | 38.2 dB |
Slew rate: | >10 V/µsec |
Input sensitivity: | 0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable |
Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
Input connectors: | 4 x XLR |
Output connectors: | 4 x Speaker, 4 x XLR feed-through output |
Circuitry: | Class D |
Protection: | Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals |
Cooling: | 2 temperature-controlled fans, front-to-rear |
Controls: | Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity |
LED indicators: | protect, clip, -5 dB, -10 dB, -20 dB (per channel) |
Construction: | steel chassis, aluminum front |
Dimensions: | 483 x 461 x 89 mm |
Rack installation with 2 U | |
Weight: | 7 kg |
Suivre cet article
Question sur le produit?
359,00 €
Disponible dans environ 6 semaine(s)
PSSO DDA-2500 Amplifier
Art. n° 10451685
Stereo PA amplifier with SMPS, 2 x 1250 W / 4 ohms
- Stereo PA amplifier with class D circuitry
- Low weight and height due to integrated switch mode power supply
- Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
- Limiter and speaker switch-on delay
- 3 operating modes can be selected (stereo, parallel or bridged)
- 2 calibrated level controls for precise level adjustment
- Input sensitivity adjustable
- LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
- Highly efficient front-to-rear air routing
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs and screw terminals
- Rugged steel chassis with aluminum front panel
- Rack installation with 2 units
Power supply: | 100-240 V AC, 50/60 Hz |
Power consumption: | 200 W (1/8 power) |
Power output (RMS): | |
Stereo, parallel at 4 ohms | 2 x 1250 W |
Stereo, parallel at 8 ohms | 2 x 700 W |
8 ohms bridged | 1 x 2500 W |
Frequency range: | 20-20000 Hz |
Signal-to-Noise ratio: | >100 dB |
Total harmonic distortion: | <0.15 % |
Damping factor: | >500 |
Voltage gain: | 39.7 dB |
Slew rate: | >10 V/µsec |
Input sensitivity: | 0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable |
Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
Input connectors: | 4 x XLR |
Output connectors: | 4 x Speaker, 4 x XLR feed-through output |
Circuitry: | Class D |
Protection: | Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals |
Cooling: | 2 temperature-controlled fans, front-to-rear |
Controls: | Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity |
LED indicators: | protect, clip, - 5 dB, - 10 dB, - 20 dB (per channel) |
Construction: | steel chassis, aluminum front |
Dimensions: | 483 x 461 x 89 mm |
Rack installation with 2 U | |
Weight: | 7.5 kg |
Suivre cet article
Question sur le produit?
399,00 €
Disponible dans environ 6 semaine(s)
PSSO DDA-3500 Amplifier
Art. n° 10451687
Stereo PA amplifier with SMPS, 2 x 1750 W / 4 ohms
- Stereo PA amplifier with class D circuitry
- Low weight and height due to integrated switch mode power supply
- Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
- Limiter and speaker switch-on delay
- 3 operating modes can be selected (stereo, parallel or bridged)
- 2 calibrated level controls for precise level adjustment
- Input sensitivity adjustable
- LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
- Highly efficient front-to-rear air routing
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs and screw terminals
- Rugged steel chassis with aluminum front panel
- Rack installation with 2 units
Power supply: | 100-240 V AC, 50/60 Hz |
Power consumption: | 300 W (1/8 power) |
Power output (RMS): | |
Stereo, parallel 4 ohms | 2 x 1750 W |
Stereo, parallel 8 ohms | 2 x 1000 W |
8 ohms bridged | 1 x 3500 W |
Frequency range: | 20-20000 Hz |
Signal-to-Noise ratio: | >100 dB |
Total harmonic distortion: | <0.15 % |
Damping factor: | >500 |
Voltage gain: | 41.2 dB |
Slew rate: | >10 V/µsec |
Input sensitivity: | 0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable |
Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
Input connectors: | 4 x XLR |
Output connectors: | 4 x Speaker, 4 x XLR feed-through output |
Circuitry: | Class D |
Protection: | Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals |
Cooling: | 2 temperature-controlled fans, front-to-rear |
Controls: | Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity |
LED indicators: | protect, clip, - 5 dB, - 10 dB, - 20 dB (per channel) |
Construction: | steel chassis, aluminum front |
Dimensions: | 483 x 461 x 89 mm |
Rack installation with 2 U | |
Weight: | 8.5 kg |
Suivre cet article
Question sur le produit?
449,00 €
Disponible dans environ 6 semaine(s)
PSSO HSP-1000 MK2 SMPS Amplifier
Art. n° 10451682
Stereo PA amplifier with integrated SMPS
- Stereo PA amplifier with class H circuitry
- Low weight and height due to integrated switch mode power supply
- Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
- Limiter and speaker switch-on delay
- 3 operating modes can be selected (stereo, parallel or bridged)
- 2 calibrated level controls for precise level adjustment
- Input sensitivity and limiter adjustable
- LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
- LEDs for parallel and bridge mode
- Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
- Highly efficient front-to-rear air routing
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs and screw terminals
- Rugged steel chassis with aluminum front panel
- Rack installation with 2 units
Power supply: | 230 V AC, 50 Hz |
Power consumption: | 1000 W (1/8 power) |
Power output (RMS): | |
Stereo 4 ohms | 2 x 500 W |
Stereo 8 ohms | 2 x 310 W |
8 ohms bridged | 1 x 1000 W |
Frequency range: | 20-20000 Hz |
Signal-to-Noise ratio: | >80 dB |
Total harmonic distortion: | <0.1 % |
Damping factor: | >200 |
Voltage gain: | 38 dB |
Slew rate: | >20 V/µsec |
Crosstalk: | >70 dB |
Input sensitivity: | 32 dB/1.0 V/0.775 V, switchable |
Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
Input connectors: | 2 x XLR |
Output connectors: | 2 x Speaker, screw terminals, 2 x XLR feed-through output |
Protection: | Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals |
Cooling: | 2 temperature-controlled fans, front-to-rear |
Controls: | Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity |
LED indicators: | parallel, bridge (globally), protect, clip, signal (per channel) |
Construction: | Steel chassis, aluminum front panel |
Dimensions: | 483 x 400 x 89 mm |
Rack installation with 2 U | |
Weight: | 8 kg |
Suivre cet article
Question sur le produit?
439,00 €
cet article n'est pas disponible actuellement
PSSO HSP-2800 MK2 SMPS Amplifier
Art. n° 10451690
Stereo PA amplifier with integrated SMPS, 2 x 1400 W
- Stereo PA amplifier with class H circuitry
- Low weight and height due to integrated switch mode power supply
- Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
- Limiter and speaker switch-on delay
- 3 operating modes can be selected (stereo, parallel or bridged)
- 2 calibrated level controls for precise level adjustment
- Input sensitivity and limiter adjustable
- LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
- LEDs for parallel and bridge mode
- Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
- Highly efficient front-to-rear air routing
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs and screw terminals
- Rugged steel chassis with aluminum front panel
- Rack installation with 2 units
Power supply: | 230 V AC, 50 Hz |
Power consumption: | 1500 W (1/8 power) |
Power output (RMS): | |
Stereo 4 ohms | 2 x 1400 W |
Stereo 8 ohms | 2 x 850 W |
8 ohms bridged | 1 x 3000 W |
Frequency range: | 20-20000 Hz |
Signal-to-Noise ratio: | >90 dB |
Total harmonic distortion: | <0.1 % |
Damping factor: | >300 |
Voltage gain: | 38 dB |
Slew rate: | >20 V/µsec |
Crosstalk: | >70 dB |
Input sensitivity: | 32 dB/1.0 V/0.775 V, swtichable |
Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
Input connectors: | 2 x XLR |
Output connectors: | 2 x Speaker, screw terminals, 2 x XLR feed-through output |
Protection: Overheat, overload, short-circuit, over-current, DC voltage, softstart, | VHF signals |
Cooling: | 2 temperature-controlled fans, front-to-rear |
Controls: | Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity |
LED indicators: | parallel, bridge (globally), protect, clip, signal (per channel) |
Construction: | Steel chassis, aluminum front panel |
Dimensions: | 483 x 505 x 89 mm |
Rack installation with 2 U | |
Weight: | 13 kg |
Suivre cet article
Question sur le produit?
829,00 €
Stock suffisant pour environ 12 semaine(s)
PSSO HSP-4000 MK2 SMPS Amplifier
Art. n° 10451694
Stereo PA amplifier with integrated SMPS, 2 x 2000 W
- Stereo PA amplifier with class H circuitry
- Low weight and height due to integrated switch mode power supply
- Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
- Limiter and speaker switch-on delay
- 3 operating modes can be selected (stereo, parallel or bridged)
- 2 calibrated level controls for precise level adjustment
- Input sensitivity and limiter adjustable
- LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
- LEDs for parallel and bridge mode
- Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
- Highly efficient front-to-rear air routing
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs and screw terminals
- Rugged steel chassis with aluminum front panel
- Rack installation with 2 units
Power supply: | 230 V AC, 50 Hz |
Power consumption: | 2000 W (1/8 power) |
Power output (RMS): | |
Stereo 4 ohms | 2 x 2000 W |
Stereo 8 ohms | 2 x 1200 W |
8 ohms bridged | 1 x 4100 W |
Frequency range: | 20-20000 Hz |
Signal-to-Noise ratio: | >80 dB |
Total harmonic distortion: | <0.1 % |
Damping factor: | >200 |
Voltage gain: | 32 dB |
Slew rate: | >20 V/µsec |
Crosstalk: | >70 dB |
Input sensitivity: | 32 dB/1.0 V/0.775 V, switchable |
Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
Input connectors: | 2 x XLR |
Output connectors: | 2 x Speaker, screw terminals, 2 x XLR feed-through output |
Protection: | Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals |
Cooling: | 2 temperature-controlled fans, front-to-rear |
Controls: | Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity |
LED indicators: | parallel, bridge (globally), protect, clip, signal (per channel) |
Construction: | Steel chassis, aluminum front panel |
Dimensions: | 483 x 505 x 89 mm |
Rack installation with 2 U | |
Weight: | 14 kg |
Suivre cet article
Question sur le produit?
799,00 €
Stock suffisant pour environ 12 semaine(s)
OMNITRONIC MCD-2004 4-Channel Amplifier
Art. n° 10452411
4-channel PA amplifier with SMPS, 4 ohms: 4 x 500 W, 8 ohms: 4 x 250 W
- PA amplifier with integrated limiter for multi-zone applications
- 4 x 500 W/4 ohms
- 8-ohm bridge operation possible
- Signal inputs via balanced XLR mounting jacks and terminal blocks
- Speaker connection via terminal blocks
- Tamper-proof level adjustment on the rear panel
- 3-fold output meter with clip LED per channel
- Speaker switch-on delay
- Fan cooling
- Robust steel chassis with aluminum front
- Complete protection set against short-circuit, overheat, overload, and DC voltage overlay at the outputs
- Rack installation with 3 units
Power supply: | 115/230 V AC, 50/60 Hz |
Power consumption: | 900 W |
Power output sine: | |
4 ohms: | 4 x 150 W |
8 ohms: | 4 x 100 W |
8 ohms bridged: | 2 x 300 W |
Frequency range: | 22-25000 Hz |
Damping factor: | >200 |
Distortion factor: | 0.01 % |
SN ratio: | 102 dB |
Channel separation (at 1 kHz): | 61 dB |
Slew rate: | >30 V/µsec |
Min. input sensitivity: | 0.77 V |
Input impedance: | 12 kohms (unbalanced), 22 kohms (balanced) |
Input connectors: | 4 x XLR female, 4 x terminal block |
Output connectors: | 4 x terminal block |
Control elements: | Power switch, level control per channel, crossover on/off per channel, high/low pass per channel, mode switch (stereo/bridged) |
Indicators: | Level with clip per channel, bridged |
Protection circuits: | Softstart, short-circuit, overheat, overload and DC voltage |
Construction: | Steel chassis with aluminum front panel |
Dimensions: | 310 x 482 x 132 mm |
Minimum mounting depth: | 320 mm |
Weight: | 7 kg |
Suivre cet article
Question sur le produit?
329,00 €
Disponible dans environ 8 semaine(s)
OMNITRONIC MCD-3006 6-Channel Amplifier
Art. n° 10452412
6-channel PA amplifier with SMPS, 4 ohms: 6 x 500 W, 8 ohms: 6 x 250 W
- PA amplifier with integrated limiter for multi-zone applications
- 6 x 500 W/4 ohms
- 8-ohm bridge operation possible
- Signal inputs via balanced XLR mounting jacks and terminal blocks
- Speaker connection via terminal blocks
- Tamper-proof level adjustment on the rear panel
- 3-fold output meter with clip LED per channel
- Speaker switch-on delay
- Fan cooling
- Robust steel chassis with aluminum front
- Complete protection set against short-circuit, overheat, overload, and DC voltage overlay at the outputs
- Rack installation with 3 units
Suivre cet article
Question sur le produit?
459,00 €
Disponible dans environ 8 semaine(s)
OMNITRONIC MCD-4008 8-Channel Amplifier
Art. n° 10452413
8-channel PA amplifier with SMPS, 4 ohms: 8 x 500 W, 8 ohms: 8 x 250 W
- PA amplifier with integrated limiter for multi-zone applications
- 8 x 150 W/4 ohms
- 8-ohm bridge operation possible
- Signal inputs via balanced XLR mounting jacks and terminal blocks
- Speaker connection via terminal blocks
- Tamper-proof level adjustment on the rear panel
- 3-fold output meter with clip LED per channel
- Speaker switch-on delay
- Fan cooling
- Robust steel chassis with aluminum front
- Complete protection set against short-circuit, overheat, overload, and DC voltage overlay at the outputs
- Rack installation with 3 units
Suivre cet article
Question sur le produit?
599,00 €
Disponible dans environ 8 semaine(s)
Votre commande a bien été envoyée.