Steinigke Showtechnic GmbH - your wholesale company for event technology. We only sell to commercial customers. All prices without tax.
Orden
Products per page:
1 2

PSSO  HSP-1000 MK2 SMPS Amplifier

N° de artículo 10451682
Características
Datos técnicos

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:1000 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 500 W
Stereo 8 ohms2 x 310 W
8 ohms bridged1 x 1000 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.1 %
Damping factor:>200
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 400 x 89 mm
Rack installation with 2 U
Weight:8 kg
Shipping weight:9.20 kg
439,00 
Existencias para 12 Sem.

PSSO  HSP-2100 MK2 SMPS Amplifier

N° de artículo 10451686
Características
Datos técnicos

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:1500 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 1050 W
Stereo 8 ohms2 x 650 W
8 ohms bridged1 x 2200 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>90 dB
Total harmonic distortion:<0.1 %
Damping factor:>300
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, swtichable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 400 x 89 mm
Rack installation with 2 U
Weight:10 kg
Shipping weight:11.50 kg
599,00 
Este artículo no está disponible

PSSO  HSP-2800 MK2 SMPS Amplifier

N° de artículo 10451690
Características
Datos técnicos

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:1500 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 1400 W
Stereo 8 ohms2 x 850 W
8 ohms bridged1 x 3000 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>90 dB
Total harmonic distortion:<0.1 %
Damping factor:>300
Voltage gain:38 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, swtichable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection: Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 505 x 89 mm
Rack installation with 2 U
Weight:13 kg
Shipping weight:14.80 kg
829,00 
Existencias para 12 Sem.

PSSO  HSP-4000 MK2 SMPS Amplifier

N° de artículo 10451694
Características
Datos técnicos

Stereo PA amplifier with integrated SMPS

  • Stereo PA amplifier with class H circuitry
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Limiter and speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 2 calibrated level controls for precise level adjustment
  • Input sensitivity and limiter adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • LEDs for parallel and bridge mode
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs and screw terminals
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:2000 W (1/8 power)
Power output (RMS):
Stereo 4 ohms2 x 2000 W
Stereo 8 ohms2 x 1200 W
8 ohms bridged1 x 4100 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.1 %
Damping factor:>200
Voltage gain:32 dB
Slew rate:>20 V/µsec
Crosstalk:>70 dB
Input sensitivity:32 dB/1.0 V/0.775 V, switchable
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:2 x XLR
Output connectors:2 x Speaker, screw terminals, 2 x XLR feed-through output
Protection:Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 505 x 89 mm
Rack installation with 2 U
Weight:14 kg
Shipping weight:15.30 kg
899,00 
Existencias para 12 Sem.

PSSO  PRIME System Amplifier DSP

N° de artículo 10451701
Características
Datos técnicos

DSP PA amplifier with real-time network communication

  • 6-channel PA amplifier with high-performance DSP, freely programmable
  • Sample frequency: 96 kHz and 64-bit technology
  • Premium components ensure excellent sound features
  • Efficient class D amplifier circuitry
  • 2 Pascal amplifier modules
  • 4 analog inputs and 2 digital AES/EBU interfaces (XLR)
  • 4 analog link outputs (XLR)
  • 2 Neutrik Speakon outputs
  • Neutrik Powercon mains input
  • Real-time remote control via built-in Ethernet LAN interface
  • User-friendly software for PC and Mac included
  • 80 presets can be stored and activated
  • Manual control via encoder, LCD screen and buttons at the front panel
  • 120 dB dynamic range
  • Flexible routing
  • 10 parametric EQ
  • X-Over: Bessel, Linkwitz-Riley, Butterworth with 24 dB/octave
  • Delay
  • Limiter and noise gate
  • Phase reverse
  • Password protection
  • Low weight and height due to integrated switch mode power supply
  • Automatic power supply adaption between 100 and 240 volts without power selector
  • Intelligent mains fuse protection
  • Input current limiter
  • Protection against turn-on and turn-off transients
  • DC protection of outputs
  • Under and over voltage protection
  • Temperature-controlled air-cooling
  • High damping factor> 1000
  • Low distortion, THD+N < 0.05 %
  • Rugged steel chassis with anodized aluminum front panel
  • Rack installation with 2 units
  • Windows XP, Vista, 7, 8 and Mac OS X 10.5.8 and better
  • Made in Germany
Power supply:100-240 V AC, 50/60 Hz
Power consumption:920 W (1/8 power)
Power output (RMS):
Channel 1, 4:2400 W at 4 ohms
1500 W at 8 ohms
Channel 2, 3, 5, 6:800 W at 4 ohms
400 W at 8 ohms
Channel 2/3, 5/6 bridged:2 x 1500 W at 8 ohms
Frequency range:20-40000 Hz
Signal-to-Noise ratio:>120 dB
Total harmonic distortion:<0.05 % (20-20000 Hz, 8 ohms)
Damping factor:>1000 (8 ohms, 1 kHz)
Voltage gain:LF 32 dB, MF 26 dB
Analog inputs:4 x XLR
Digital inputs:2 x AES/EBU (XLR)
Analog output:4 x XLR (link)
2 x 8-pin Speakon
Communication:LAN (TCP/IP)
Protection:Intelligent mains fuse protection, input current limiter,
protection against turn-on and turn-off transients, DC protection of outputs,
under and over voltage protection
Cooling:temperature-controlled air-cooling
Controls:Power switch, encoder, menu, exit
LED indicators:Protect, Peak, Limit, Signal
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 482 x 88 mm
Rack installation with 2 U
Weight:12 kg
Shipping weight:13.50 kg
3.150,00 
Existencias para 12 Sem.

PSSO  QCA-10000 4-Channel SMPS Amplifier

N° de artículo 10451697
Características
Datos técnicos

4-channel PA amplifier with integrated SMPS

  • 4-channel PA amplifier with class I circuitry
  • 4 x 2100 W/4 ohms
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 4 level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
  • Neutrik Speakon outputs
Power supply:230 V AC, 50 Hz
Power consumption:1150 W (1/8 power)
Power output (RMS):
2 ohms4 x 2500 W
4 ohms4 x 2100 W
8 ohms4 x 1300 W
4 ohms bridged2 x 5000 W
8 ohms bridged2 x 4200 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.05 %
Damping factor:>800
Slew rate:>10 V/µsec
Crosstalk:>65 dB
Input sensitivity:0.775 V/1.0 V/1.4 V/38 dB/32 dB/26 dB, switchable
Voltage gain:40.3 dB (0.775 V), 38 dB (1.0 V), 35.1 dB (1.4 V)
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Protection: Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:Protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 445 x 89 mm
Rack installation with 2 U
Weight:15.7 kg
Shipping weight:15.80 kg
1.499,00 
Existencias para 12 Sem.

PSSO  QCA-6400 4-Channel SMPS Amplifier

N° de artículo 10451696
Características
Datos técnicos

4-channel PA amplifier with integrated SMPS

  • 4-channel PA amplifier with class I circuitry
  • 4 x 1400 W/4 ohms
  • Low weight and height due to integrated switch mode power supply
  • Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
  • Speaker switch-on delay
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • 4 level controls for precise level adjustment
  • Input sensitivity adjustable
  • LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
  • Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
  • Highly efficient front-to-rear air routing
  • Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
  • Speaker outputs via lockable Speaker plugs
  • Rugged steel chassis with aluminum front panel
  • Rack installation with 2 units
  • Neutrik Speakon outputs
Power supply:230 V AC, 50 Hz
Power consumption:820 W (1/8 power)
Power output (RMS):
2 ohms4 x 1600 W
4 ohms4 x 1400 W
8 ohms4 x 800 W
4 ohms bridged2 x 3200 W
8 ohms bridged2 x 2800 W
Frequency range:20-20000 Hz
Signal-to-Noise ratio:>80 dB
Total harmonic distortion:<0.05 %
Damping factor:>800
Slew rate:>10 V/µsec
Crosstalk:>65 dB
Input sensitivity:0.775 V/1.0 V/1.4 V/38 dB/32 dB/26 dB, switchable
Voltage gain:40.3 dB (0.775 V), 38 dB (1.0 V), 35.1 dB (1.4 V)
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:4 x XLR
Output connectors:4 x Speaker, 4 x XLR feed-through output
Protection: Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals
Cooling:2 temperature-controlled fans, front-to-rear
Controls:Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity
LED indicators:Protect, clip, signal (per channel)
Construction:Steel chassis, aluminum front panel
Dimensions:483 x 445 x 89 mm
Rack installation with 2 U
Weight:15.5 kg
Shipping weight:15.30 kg
1.299,00 
Existencias para 12 Sem.

OMNITRONIC  SMA-1000 Amplifier

N° de artículo 10451084
Características
Datos técnicos

Stereo PA amplifier with integrated limiter and SMPS 2 x 500 W/4 ohms

  • Low weight and height due to integrated switch-mode power supply
  • Temperature-controlled fan, particularly quiet during operation
  • Limiter and speaker switch-on delay
  • Switchable bass-boost at 80 Hz with 6 dB level increase
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • Selectable input sensitivity
  • 2 level controls
  • 3 LEDs for each channel for activated protective circuit (protect) overload (clip) and signal
  • 2 LEDs for parallel and bridge operation
  • Complete protection set against short-circuit, overheat, DC voltage and VHF signals
  • Electronically balanced inputs via XLR mounting jacks, with feed-through output (stereo RCA/6.3 mm jack)
  • Speaker outputs via lockable Speaker plugs
  • Class AB circuitry
  • Robust steel chassis
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:598 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 482 W
stereo 8 ohms2 x 340 W
8 ohms bridged1 x 1000 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>150
Distortion factor:0.05 %
Slew rate:>20 V/µsec
S/N ratio:>90 dB
Channel seperation:>70 dB/ 1 kHz
Input sensitivity:26 dB/32 dB (2.48 V/1.244 V), switchable
Voltage gain:26 dB/32 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:stereo XLR
Output connectors:stereo Speaker, feed-through output (stereo RCA, stereo 6.3 mm jack)
Circuitry:class AB
Control elements:power switch, level control per channel, mode switch (stereo/parallel/bridged), sensitivity selector, peak filter selector
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Protection circuits:short-circuit, overheat, DC voltage, VHF signals, softstart
Construction:steel chassis
Dimensions (DxWxH):390 x 483 x 92 mm (19", 2 U)
Weight:7 kg
Shipping weight:9.65 kg
359,00 
Existencias para 12 Sem.

OMNITRONIC  SMA-1500 Amplifier

N° de artículo 10451086
Características
Datos técnicos

Stereo PA amplifier with integrated limiter and SMPS 2 x 750 W/4 ohms

  • Low weight and height due to integrated switch-mode power supply
  • Temperature-controlled fan, particularly quiet during operation
  • Limiter and speaker switch-on delay
  • Switchable bass-boost at 80 Hz with 6 dB level increase
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • Selectable input sensitivity
  • 2 level controls
  • 3 LEDs for each channel for activated protective circuit (protect) overload (clip) and signal
  • 2 LEDs for parallel and bridge operation
  • Complete protection set against short-circuit, overheat, DC voltage and VHF signals
  • Electronically balanced inputs via XLR mounting jacks, with feed-through output (stereo RCA/6.3 mm jack)
  • Speaker outputs via lockable Speaker plugs
  • SMA-1500 and SMA-2000 with additional pairs of screw terminals for 8 ohms bridge operation
  • Class 2 H circuitry
  • Robust steel chassis
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:522 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 743 W
stereo 8 ohms2 x 480 W
8 ohms bridged1 x 1500 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>150
Distortion factor:0.05 %
Slew rate:>20 V/µsec
S/N ratio:>90 dB
Channel seperation:>70 dB/ 1 kHz
Input sensitivity:26 dB/32 dB (3.1 V/1.55 V), switchable
Voltage gain:26 dB/32 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:stereo XLR
Output connectors:stereo Speaker, 2 pairs of screw terminals, feed-through output (stereo RCA, stereo 6.3 mm jack)
Circuitry:class 2 H
Control elements:power switch, level control per channel, mode switch (stereo/parallel/bridged), sensitivity selector, peak filter selector
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Protection circuits:short-circuit, overheat, DC voltage, VHF signals, softstart
Construction:steel chassis
Dimensions (DxWxH):390 x 483 x 92 mm (19", 2 U)
Weight:9 kg
Shipping weight:11.80 kg
479,00 
Existencias para 12 Sem.

OMNITRONIC  SMA-2000 Amplifier

N° de artículo 10451088
Características
Datos técnicos

Stereo PA amplifier with integrated limiter and SMPS 2 x 1000 W/4 ohms

  • Low weight and height due to integrated switch-mode power supply
  • Temperature-controlled fan, particularly quiet during operation
  • Limiter and speaker switch-on delay
  • Switchable bass-boost at 80 Hz with 6 dB level increase
  • 3 operating modes can be selected (stereo, parallel or bridged)
  • Selectable input sensitivity
  • 2 level controls
  • 3 LEDs for each channel for activated protective circuit (protect) overload (clip) and signal
  • 2 LEDs for parallel and bridge operation
  • Complete protection set against short-circuit, overheat, DC voltage and VHF signals
  • Electronically balanced inputs via XLR mounting jacks, with feed-through output (stereo RCA/6.3 mm jack)
  • Speaker outputs via lockable Speaker plugs
  • SMA-1500 and SMA-2000 with additional pairs of screw terminals for 8 ohms bridge operation
  • Class 2 H circuitry
  • Robust steel chassis
  • Rack installation with 2 units
Power supply:230 V AC, 50 Hz
Power consumption:575 W (1/8 power)
Power output sine:
stereo 4 ohms2 x 1000 W
stereo 8 ohms2 x 637 W
8 ohms bridged1 x 2000 W
Frequency range:20-20000 Hz, ±0.5 dB
Damping factor:>150
Distortion factor:0.05 %
Slew rate:>20 V/µsec
S/N ratio:>90 dB
Channel seperation:>70 dB/ 1 kHz
Input sensitivity:26 dB/32 dB (3.46 V/1.73 V), switchable
Voltage gain:26 dB/32 dB
Input impedance:20 kohms (balanced), 10 kohms (unbalanced)
Input connectors:stereo XLR
Output connectors:stereo Speaker, 2 pairs of screw terminals, feed-through output (stereo RCA, stereo 6.3 mm jack)
Circuitry:class 2 H
Control elements:power switch, level control per channel, mode switch (stereo/parallel/bridged), sensitivity selector, peak filter selector
LED indicators:parallel, bridge (globally), protect, clip, signal (per channel)
Protection circuits:short-circuit, overheat, DC voltage, VHF signals, softstart
Construction:steel chassis
Dimensions (DxWxH):390 x 483 x 92 mm (19", 2 U)
Weight:9 kg
Shipping weight:12.00 kg
559,00 
Existencias para 12 Sem.
1 2
Last seen products
Your request was successful sent.
Loader
Please wait while the page is loading...

We use cookies to ensure you get the best user experience on our website. By continuing, you accept the cookie use